*

Smith and Wesson model 41 Target Pistol maintenance


*
Step #2
*
Step #3
*
Step #4 Lift the barrel assembly off of the structure and collection it aside. cleaning or inspection have the right to be performed on the barrel assembly individually from the remainder of the pistol. A breech put cleaning stick or deep chamber cleaning is best completed at this time.

You are watching: Smith and wesson model 41 disassembly

*
Step #5
*
Step #6 The on slide assembly is now moved forward to separate it from the frame.The pistol is now separated into it"s three main materials - barrel, frame, and also slide.
*
Step #7 Reassembly is completed in reverse order.Place recoil spring assembly top top frame and then download the on slide onto the frame
*
Step #8
*
Step #9
*
action #10
*

Back to peak of page

Slide detailed Disassembly and Reassembly

Click picture to enlarge snapshot

Step #1 On the best side the the slide, find the crosspin and also drift it left with a non-marring punch.
*
Step #2 Drift the crosspin fully out that the on slide assembly. Through the crosspin removed the shooting pin and also spring will drop the end of the bottom that the slide.
*
Step #3 Use a non-marring beat to drift the bolt assembly forward, the end of the slide.
*
Step #4 Once the extractor claw gets rid of the slot, the bolt assembly deserve to be eliminated from the slide.
*
Step #5 Once the bolt is removed from the slide, the extractor claw deserve to be removed.
*
Step #6 The extractor plunger and also plunger spring can be gotten rid of from the slide slot.
*
Step #7 The bolt assembly is composed of the following materials - shoot pin and return spring, extractor plunger and spring, extractor hook, bolt housing, and crosspin (also serves as the firing pin stop).
*
Step #8 To reassemble the slide. An initial install the extractor spring and also plunger.
*
Step #9 Place extractor hook onto the bolt housing.
*
Step #10 Carefully on slide the bolt housing and also extractor into the slide. Once seated, place the crosspin in the left side of slide to save the bolt organized in place. Take care to certain the grooved finish of crosspin is positioned outward.
*
Step #11 Turn on slide assembly over, location firing pin and also spring into the bolt with the groove facing upwards.
*
Step #12 Use a tool to press in the firing pin, press in the crosspin come lock the firing pin in place.
*
Step #13 Use a non-marring beat to chair the crosspin into the slide till it sits flush with the next of the slide. On slide reassembly is complete.
*

Back to height of page

Trigger convey Procedures

Click picture to enlarge photo

Step #1 First field strip the pistol as defined above. Then loctate the trigger pivot pin. The pivot pin should be drifted from the appropriate towards the left side of the frame. The only has to be drifted part way to change the cause pull ~ above the design 41.
*
Step #2 The trigger adjustment lever is situated inside the frame. Drifting the trigger pivot pin approximately fifty percent way across the framework will permit clearance for adjustment lever movement.
*
Step #3 Lay part masking tape onto the right side the the frame to prevent any type of surface marring from tool slippage.
*
Step #4 Use a 3/32" pin beat to drift the pivot pin.
*
Step #5 Drift the trigger pivot pen part way into the frame.
*
Step #6 Ensure the create pivot pen is clear of the adjustment lever.
*
Step #7 Adjustments deserve to be make by relocating the lever forwards or rearwards in the frame. Each bar graduation is roughly 1/4 pound of adjustment. The cause can be adjusted between 2 - 3 pounds by selecting an suitable lever position.
*
Step #8 Once the desired lever place is selected, drift pin to ideal far sufficient to check the cause pull. Make an ext adjustments as important by relocating the pin and lever.
*
Step #9 Once wanted pull load is achieved, drift the cause pivot pen to the best until the pin is flush with the left side of the frame. Reassemble pistol and test accordingly by live firing.
*

Back to height of page

Extractor Tuning mediate Procedure

Click picture to enlarge photo


This procedure was an initial developed to aid reduce S&W model 41 ejection troubles by the so late pistolsmith Austin Behlert. remove the on slide from the pistol by ar stripping. Test the extractor’s holding capacity by placing a ring under the hook on do the washing up on the bolt face. Gently shake the slide earlier and forth. If the instance falls off, climate the extractor is no to hold the situations securely against the bolt face. The extractor can be tuned by utilizing the complying with steps.
Remove the extractor hook native the bolt assembly by adhering to the on slide disassembly direction above.
Place the extractor hook in a drill press vise. Tighten the vise jaws under just sufficient to put a slight bending (or bow) in the ago side that the extractor hook – a few thousandths of an inch is every you’re make the efforts to attain by this process. Fist – end tightening the vise jaws will break the M-41 extractor!
Use a pointed pin punch and tap the lightly with a hammer, in a stippling action, come make small dimples follow me the ago side that the extractor. This dimples relieve the strain on the hardened stole and allow the extractor come conform come the brand-new shape without having actually to re-heat law it.
Next lightly file the roughened dimples to smooth the end the extractor’s surface. Submit the extractor surface permits it to relocate smoothly as soon as inside the slide’s extractor slot. Re-blue the extractor after filing and also replace it in the bolt.

Back to optimal of page

Magazine Disconnector Operation

*
The create bar is required downwards by the newspaper disconnector bar when a newspaper in no installed. The magazine disconnector lever is spring loaded to press downwards. Once the trigger bar is down the sear is disengaged, and the hammer can not be exit by an operator pulling the trigger. The height (curved shark fin) part of the create bar additionally has a disconnector function. Once the on slide is out of battery the fin is forced downward through the slide, this disconnects the sear and prevents the pistol from being discharged.

See more: Can Starfish Come Back To Life, Can Starfish Survive Out Of Water

*
The cause bar is compelled upwards as soon as a newspaper is installed. The magazine disconnector lever is driven upwards by the create bar return spring. As soon as the create bar is up, the sear is now engaged by it and the hammer deserve to be released by an operator pulling the trigger. The top (curved shark fin) section of the cause bar is now aligned v the cut-out recess in the slide. When the slide is close up door it"s in battery, this permits the sear come be engaged by the create bar and the pistol can be discharged.

Back to peak of page