*
*

*
How To: Cabin wait Filter for 1998 - 2000 Civic
Okay, as you may or might not know, the "96-"00 civic came v a cabin waiting filter... Simply not in the US. Don"t asking me why, however though our USDM Civics v air conditioning have actually all the tools to have a cabin waiting filter, we perform not have the really cabin wait filter assembly, no one is it noted in the USDM EPC because that our cars.But, this is just how you can make your "98-"00 civic have a cabin air filter. "96-"97 models carry out not have actually the very same assembly and also cannot perform this mod so easily!The following photos room of a USDM 1998 Honda public EX coupe. Other years and trims can have slim differences.SuppliesPhillips reminder Screwdriver10mm Ratcheting Wrench/Socket8mm Ratcheting Wrench/SocketNeedle nose PliersFlashlightBottle BrushVacuumPartsCabin waiting Filter Parts*:- "97-"01 CR-V / "00-"06 understanding Cabin waiting Filter --- us Honda part No.: 80291-ST3-E01 - List: $21.98 --- EDM Honda component No. (Civic): 80291-ST3-505 - List: $21.98 --- Bosch component No.: P3753 - List: $19.99- "97-"01 CR-V / "00-"06 insight / "96-"00 EDM civic Cabin waiting Filter framework --- Honda component No.: 80292-ST3-E01 - List: $13.74* I"d introduce you acquisition these parts all individually instead of as a full filter assembly. The perform for the complete assembly is $55.93, while the parts separately which consist of the assembly cost a complete of $39.25 for some reason.Installation Instructions*NOTE* You can skip some of the dashboard removal if you happen to have a ratcheting 8mm wrench.

You are watching: 1998 honda civic cabin air filter

*
*
First, you"re walk to need to pull off her driver"s side knee bolster panel. There"s a screw above the coin pocket towards the door, and also one top top either corner of the bottom the the panel. There will additionally be one in the top corner next come the facility of the dash. When all those screws are gotten rid of you can pull the dashboard off. There will be a couple of metal clips along the peak of the panel.Then drop the glovebox by advertise the political parties in to let it clear the framework it fits into. You deserve to just let it hang there if you wish, or you have the right to remove that by removed the screws at the bottom that the box.Now get to job-related on the screws and bolts holding the 12 volt panel on above the cup holders. There will be a screw or bolt in each of the 4 corners (the reduced glove box side corner will have a 10mm bolt) and also then two screws right over the 12 volt plug. In the photograph the 12 volt panel has been changed with one ashtray and also lighter, yet the hardware is quiet in the very same locations.All of that just to gain to one 8mm bolt (which is behind the center component of the dash, shown in the an initial color photo below).
*
*
Remove the screw in ~ the peak of the trim piece on the ideal side that the glovebox. There space three steel clips stop this piece on, so it could take some muscle to take the dashboard off.
*
If friend haven"t already, remove the 8mm/Phillips tip bolt in the lower left next of the glovebox frame. Then remove the 10mm bolt, to add the 8mm bolt close to it which was simply behind the 12 volt panel.
*
Remove the two 8mm bolts and the 10mm bolt indigenous the reduced right side of the glovebox frame too.Make sure you"re holding onto the steel bar and also glovebox (if you have not eliminated it native the bar) so that no damage is done as soon as you eliminate the last bolt ~ above the bar.
*
You will see a tall black rectangular item with a manage sticking out. This is the evaporator lid. Use needle nose pliers come pinch the white clip hold the wire harness on. The clip top top the right might be less complicated to unclip if you usage a flathead little bit to push the edges of the clip in since of the absence of space. Then remove the screw that is holding the metal bracket on right in front of the evaporator lid.Lift the edge of the optimal of the lid up and also then perform the very same on the the bottom.
*
There that is. That"s where the cabin air filter sits. It could be apparent that currently would be a good time to clean that out. Come the left you can see the metal evaporator. I supplied a bottle brush to remove the debris from the mesh and then carefully vacuumed it every up.

See more: How To Tell What Key Is This Piece In? How To Determine The Key Of A Song

*
*
*
Put the filter right into the frame, making sure that the air circulation directions match.
*
The "97-"01 CR-V / "00-"06 insight cabin wait filter assembly will fit in right here perfectly.Once you download the filter, assembly is the contrary of disassembly.
*